DOCOMO, NTT, NEC and Fujitsu Develop Top-level Sub-terahertz 6G Device
April 12, 2024 | JCN NewswireEstimated reading time: 2 minutes
NTT DOCOMO, INC., NTT Corporation, NEC Corporation and Fujitsu Limited jointly announced today the development of a top-level (1) wireless device capable of ultra-high-speed 100 Gbps transmissions in the 100 GHz and 300 GHz sub-terahertz bands.
The four companies have been jointly conducting R&D on sub-terahertz devices since 2021 in anticipation of the coming 6G era. To date, tests of a jointly developed wireless device have achieved ultra-high-speed 100 Gbps transmissions in the 100 GHz and 300 GHz bands at distances of up to 100 meters.(2) By comparison, 100 Gbps is approximately 20 times faster than the maximum 4.9 Gbps (3) data rate of current 5G networks.
The roles and achievements of the four participating companies are described below.
DOCOMO
After analyzing the wireless system configuration and performance required for 100 GHz telecommunications applications, DOCOMO developed wireless transmission equipment capable of transmitting data rates equivalent to 100 Gbps at a distance of 100 meters.
NTT
Based on research into 300 GHz wireless devices and related equipment such as wideband mixers, NTT developed a top-level wireless device capable of transmitting 100 Gbps per channel at a distance of 100 meters in the 300 GHz band.(1)
NEC
After analyzing a wireless system configuration for telecommunications in the 100 GHz band, NEC developed a multi-element active phased array antenna (APAA) (1) consisting of more than 100 antenna elements.
Fujitsu
After researching compound semiconductor technologies that enable high-output, high-efficiency signal amplification to extend communication range and reduce power consumption in the 100 GHz and 300 GHz bands, Fujitsu achieved the world's highest power efficiency (4) in a high-output amplifier.
In the 6G era, when wireless networks are envisioned supporting diverse applications ranging from ultra-HD video streaming to real-time control in autonomous vehicles, as well as increasing communication demands, high-capacity wireless communication is expected to be achieved by exploiting the abundant bandwidth available in the sub-terahertz band from 100 GHz to 300 GHz. However, compared to 28 GHz and other millimeter bands used in current 5G systems, the much higher frequencies of the sub-terahertz band will require entirely different wireless devices that are now being developed from scratch. To be successful, this effort will need to overcome several key challenges, such as determining the specific performance requirements of wireless devices operating in the sub-terahertz band, and then actually developing such devices.
Going forward, the four companies will continue to conduct extensive R&D into sub-terahertz telecommunications, leveraging each company's strengths in various initiatives to contribute to 6G standardization.
(1) This assumes that as of March 2024, no other entity has announced 1) achievement of 100 Gbps transmission over a distance of 100 meters in the 100 GHz band (according to NEC); 2) achievement of 100 Gbps transmission over a distance of 100 meters in the 300 GHz band (according to NTT); and 3) achievement of an equivalent isotropic radiation power (EIRP) of 50 dBm and a beam steering angle of approximately ±30 degrees using 100 or more APAA elements in the 100 GHz band (according to NEC).
(2) The transmitter and receiver are facing each other in a straight line with no obstacle between them.
(3) Maximum values specified in technical standards, but not representing the actual data rate, provided on a best-effort basis. Actual data rates may vary depending on the communication environment and network congestion.
(4) World's highest efficiency under specific high-power conditions in the 100 GHz and 300 GHz bands, respectively, according to Fujitsu as of March 2024.
Suggested Items
epoxySet Unveils UC-2210M - Urethane for Electronic Component Protection
04/29/2024 | epoxySetepoxySet introduces a new and unique, urethane potting compound. The UC-2210M was formulated to protect electronic components in high moisture and thermal environments including constant atmospheric exposure, oceanographic environments and high humidity conditions.
Peters’ ELPEGUARD SL 1800 FLZ Now Also Certified for Outdoor Applications
04/29/2024 | PetersThe conformal coating ELPEGUARD® SL 1800 FLZ from Peters has been awarded an extended UL certificate. The UL 746 E rating certifies that the acrylate-based coating for printed circuit boards, besides featuring the highest non-flammability rating UL V-0, is also suitable for outdoor use.
epoxySet Introduces EO-20E – Versatile, Electrically Conductive Epoxy
04/29/2024 | epoxySetepoxySet produces EPOXIOHM EO-20E an industry established, reliable electrically conductive epoxy designed for solder replacement, chip bonding and other intricate electronic and optoelectronic assemblies. This creamy paste has a an easy to use 1:1 mix ratio with a 48 hour work time.
SCHWEIZER Confirms Group Figures and Outlook for 2024
04/29/2024 | SCHWEIZERSCHWEIZER announces the publication of the annual report for 2023 and confirms the preliminary figures. The SCHWEIZER-Group (according to IFRS) generated sales of EUR 139.4 million in 2023 (previous year: EUR 131.0 million).
Arlon Electronic Materials Awarded Requalification to IPC-4101 QPL for All Polyimide Specification Sheets
04/29/2024 | IPCIPC's Validation Services Program has awarded Arlon Electronic Materials Division, an electronics material manufacturing company headquartered in Rancho Cucamonga, Calif., an IPC-4101 Qualified Products Listing (QPL) requalification for the third time.