Understanding MIL-PRF-31032, Part 4
October 20, 2020 | Anaya Vardya, American Standard CircuitsEstimated reading time: 3 minutes
Overview
Continuing with Part 4 of the discussion on understanding the military PCB performance standard MIL-PRF-31032, the next step in the process is to create four new procedures to address the unique requirements of the military.
Qualification and Add-On Procedure
This process provides the guidelines for the initial qualification of the company, as well as a path for future add-on qualifications. The first thing that needs to be included is the process for developing the qualification test vehicle. This is the specific PCB design that will be used to build the qualification boards. The documentation required must also be identified, such as production traveler, test vehicle design, drawings, multilayer layup, etc.
Test Vehicle
A company will qualify for specific technology and will need to develop a qualification test plan, which is a document that specifies the following minimum attributes of the qualification board:
- Max. Number of Layers and Dielectric Type
- Max. Panel Size
- Max. Board Thickness
- Min. Drilled Hole Before Plating
- Aspect Ratio
- Min. Conductor Width
- Via Structure
- Min. Conductor Space
- Hole Preparation
- Hole Wall Conductive Coating
- Copper Plating
- Solder Resist
- Silkscreen
- Final Finish
- Additional Fabrication Capabilities
- Controlled Impedance
It is important to note here that the qualification “flows down” but not “up.” In other words, if an 18-layer is qualified, layer counts less than 18 layers can be built as long as the other above parameters are the same, but a 20-layer would not be allowed.
Sample Size and Data Requirements
The next section would be to establish the lot size of the qualification lot and the sample sizes that will be used for testing. The data recording and retention of all qualification records must be defined, including coupons and any extra boards left over from the qualification lot.
Failure Analysis and Resubmission
A DLA-approved third-party testing lab must be selected to use for the initial qualification as well as the ongoing monthly testing. Should a submitted sample fail any tests, this procedure needs to have a provision for failure analysis and corrective action. This typically leverages the existing processes already in place. The rules for resubmitting new qualification boards must also be defined here, particularly that additional extra samples from the failed lot cannot be used.
Qualification Test Summary and Reporting
This section outlines the components for the summary that is needed to be submitted to the DLA after all tests and inspections have been successfully performed, including the third-party lab). This includes things like the travelers, internal and external test and inspection results, lot conformance forms and results, failure mode for any rejections, dimensional and electrical test parameters and measurements, and a copy of the qualification test plan.
Add-On Qualification
MIL-PRF-31032 allows for the expansion of the qualified technology through the add-on qualification process. A technology that falls within 25% of the current qualified technology can be built with a new qualification test plan and TRB approval. For example, with a qualified 18-layer, a 22-layer could be qualified through the add-on process.
The same would apply to line width, hole size, etc. There is no need to wait for DLA approval in these cases; they will verify the add-on qualification data during their next regular visit/audit. Anything greater than a 25% technology change will require a new full qualification like the initial qualification.
Conclusion
This wraps up qualification and add-on procedures. Part 5 will focus on the next unique procedure needed to produce MIL-PRF-31032 PCBs.
Editor’s note: Read Part 1, Part 2, and Part 3.
Anaya Vardya is president and CEO of American Standard Circuits; co-author of The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals; and author of Thermal Management: A Fabricator's Perspective. Visit I-007eBooks.com to download these and other free, educational titles. He also co-authored “Fundamentals of PCB Technology.”
Suggested Items
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation are proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia. on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.