Are There Advantages to Changing Your Registration System?


Reading time ( words)

I recently had a conversation with DIS's Tony Faraci at IPC APEX EXPO 2015, to learn more about their pinless registration system. What was most interesting to me are the  potential advantages a pinless system offers and if so, why the process has not been widely adopted.

Barry Matties: Hello, Tony. Thanks for sitting down with me today. Could you please tell us about the DIS pinless registration system?

Tony Faraci: Yes, thanks, Barry. What is happening with this type of a system, as opposed to a conventional pin lamination technology, is that we are optically aligning all the internal layers of a panel. Conventional wisdom used to be that you would post-etch punch all your cores and then pin. Now, you are eliminating that whole process. You are eliminating pinning, you're eliminating all of that punching and all of that pin tooling and now we are optically aligning all the layers and tack bonding them together.

By optically aligning, all those mechanical pin tolerances are eliminated, and of course you are not limited to certain panel sizes. The layers are aligned optically and then we use an induction bonding system that actually bonds the layers together. The advantage here is that the registration can be checked before lamination, which really can't be done with any type of pinning system.

You can kind of do it with a riveting system, let's say, or eyelets, but with this type of system, now you can check your registration before going into the lamination press, then you laminate the panel, come out, and now you can again check the registration of that panel. Having the data immediately before and after lamination can show what's happening inside the press.

Besides this valuable data set, this is also telling you what our system is doing. It's giving you an overall view at different points of the process which they've never been able to do before. You can kind of do it with a riveting system but you're not going to do such high layer counts and it will not be repeatable. So DIS pinless technology is the next step up from pin because it eliminates all those mechanical problems.

Matties: For those who already have a pin system in place, are there any special processes or changes that they have to make?

Faraci: It changes a little bit in the process. What you're doing is using similar targets like they do on a punching machine, but now they are adding these welding coupons. They are just a quarter-inch by three-quarter-inch solid copper pads at four points on the panel that we'll use to tack bond.

Where it really changes is the reduced handling and lay-up. The machine is basically an optical lay-up machine, so instead of handling the panel once at post-etch punch and then going through oxide or oxide alternative, where there is some more stretching of the layer, and then laying up on mechanical pins, where most of the bulk error is, we’re only handling it once, at optical lay-up.

We're not selling a product that's competing against the post-etch punch; it's a process change. It eliminates that pin-up process and instead is optically aligning the layers; this really is the biggest change.

It's a little bit different in the process, so there is a learning curve. But the benefit for the customer is great, because now they can start looking at what's happening in the press. Today, most high-end shops work with pins, so what do they do, they lay up a book and you don't know if there's a shift -did it happen at lay-up, did it happen in the press, did it happen at transport?

So, that's one of the biggest changes. Another product that we developed about six years ago was a multi-camera system that allows us to check the layers front to back, in order to figure out where the best fit positions are for that layer. That also works well with our systems, because that data gets captured and it goes into our alignment systems.

Matties: How does that benefit?

Faraci: Let's say a customer is running higher-end boards. They can, if they have an LDI process for example, print a 2D bar code on every layer, serialize the core, and then our multi-camera system can actually measure that core and capture the positional data. And of course it's tied to that serial number.

Then when it gets to our alignment machines, they read that barcode and they know the positional data of that core, based on the eight targets, and now we can process the panel. So it enables all our existing two-camera machines—for example, what they have at DSG—once customers buy this unit, they’re able to have it work like an eight-camera system. Or you could use it off line just to measure panels to make sure that the layers are within tolerance before you use them at lay-up.

Matties: So, with your system the border is now smaller?

Share

Print


Suggested Items

Catching Up With RBP Chemical and Schlötter

01/20/2022 | Dan Beaulieu, D.B. Management Group
It’s always great to see two very good companies form a mutually beneficial alliance. I was lucky enough to watch this particular strategic partnership come to fruition this year between RBP Chemical and Schlötter. I wanted to talk to both companies, so I sat down with Matthias Hampel, global executive representative-PCB and electronics at Schlötter, and Ernest Litynski, president of RBP Chemical Technology, to get the inside story.

Technology and Development Prospects for the European Marketplace

01/18/2022 | Nolan Johnson, I-Connect007
Nolan Johnson speaks with Tarja Rapala-Virtanen technical director of the EIPC who breaks down the current state of the European market and which technologies and market segments are seeing growth.

A Tour of the New Isola Factory: Investing in North America

12/23/2021 | Barry Matties, I-Connect007
Barry Matties recently toured Isola’s new 118,000-square-foot low-volume, high-mix manufacturing facility in Chandler, Arizona. The facility’s construction began in 2020 and, like many building projects, was delayed because of the COVID-19 pandemic. Building a new factory during the pandemic was certainly a challenge but the team persevered and the new greenfield facility is now operating to meet the needs of the North American market. During the tour, Barry met with Travis Kelly, Ed Kelley, Sean Mirshafiei, Jenny Inocencio, and Walt Niziolek. They covered a range of topics, including lab operations, hiring, the supply chain, R&D, and the concept of the new facility. The factory was designed to extensively utilize automation to improve efficiencies and, as Travis Kelly stated, “to de-risk the labor shortage issue.”



Copyright © 2022 I-Connect007. All rights reserved.