Standard of Excellence: Preparing for the Future with the Right Supplier

anaya-headshot.jpgIs your PCB supplier ready to take you into the future? Sure, they are doing a good job today, but what about tomorrow? What will happen when new designs require boards to be made with thermal or RF materials, or have lines widths down to two mils?

Your R&D department is already working on products for the future. These projects will require your PCB suppliers to provide you with innovative technologies. They will have to keep up with your needs when the time comes. It is not a good time to find out that your PCB vendor base cannot support your new products at the moment when you are ready to launch them, and it’s no time to look for new PCB suppliers when you are in a time-to-market crunch!

To avoid this kind of technology gap due to supplier shortcomings, here are 12 checkpoints to make sure your PCB suppliers are ready to meet your future needs:

  1. Are they financially sound? Suppliers should have enough funds to keep up with the latest equipment and technology.
  2. Do they have the right attitude to invest in their future? Suppliers should have foresight and an understanding of what they need to do to remain cutting edge.
  3. Do they have the right people and are they easy to work with? Equipment alone does not keep a company’s technology sound. Suppliers should be well informed about new innovations occurring in the industry.
  4. Does the supplier listen to your needs?
  5. Does the supplier have the right qualifications, registrations, and certifications?
  6. Is the supplier willing to invest their time, energy, and talent to support you?
  7. Besides buying equipment, is the supplier keeping up with the latest software offerings, including CRM and process control and quality software systems?
  8. Are they willing to be your R&D partners? Suppliers should be ready to learn, experiment, and take the time to develop the right processes to build the PCBs you need.
  9. Do you share the same vision? Suppliers should move in a direction that enables them to handle your future PCB needs.
  10. Can you trust the supplier to not show your newly designed PCBs to others? All the NDAs in the world will not help you if your supplier does not respect your confidentiality.
  11. Is the supplier willing to share their expenses and resources on an R&D project with you? Or are they too busy working on their everyday PCB requirements to invest in yours?
  12. Do they know more than you do about PCBs? You need suppliers to be knowledgeable consultants, leaders, and experts that will handle all of your needs for years to come.

Overall, your supplier should be able to fulfill your PCB needs today and in the future. They should build your current PCB requirements and make time to work with you to develop the right processes for your future.

Anaya Vardya is the president and CEO of American Standard Circuits.

Back

2018

Standard of Excellence: Preparing for the Future with the Right Supplier

08-13-2018

Is your PCB supplier ready to take you into the future? Sure, they are doing a good job today, but what about tomorrow? What will happen when new designs require boards to be made with thermal or RF materials, or have lines widths down to two mils?

View Story

Material Selection: The Key to RF/Microwave Success

07-23-2018

This month's column is written by Anaya Vardya and John Bushie. In today’s environment, there are a number of suppliers that may have similar materials but price points and lead times may vary. If you are open to trying different options, it is a good idea to work closely with your PCB fabricator so they can educate you on these aspects. Another option is to do parallel builds with multiple materials in the early stages of honing a new design to determine the optimum material set.

View Story

Standard of Excellence: Making Your PCB Fabricator Your PCB Partner

06-12-2018

Are your PCB needs exceeding your vendor base’s capabilities? Do you feel that your suppliers are no longer able to keep up with your PCB needs? Do your designers feel limited by your vendors’ limited capabilities? Are you finding an issue locating alternate sources for PCBs due to the consolidation of the larger shops in our industry? If so, you are not alone.

View Story

Standard of Excellence: 5 Things a Total Global Solutions Supplier Can Provide

01-10-2018

Our world now extends far beyond the traditional brick and mortar of the domestic board suppliers of yesteryear. Now our customers demand that PCB fabricators provide them with a complete and total printed circuit board solution, from domestically built ITAR-registered defense and aerospace boards to high-volume, offshore solutions.

View Story
Back

2017

Standard of Excellence: Customers are Shooting for the Stars—Are We Coming?

08-17-2017

For years we have been calling them “science projects,” those PCB orders that did not quite fit into our normal process stream and therefore needed special attention, as well as special handling. Often, we have had to use trial and error to come up with just the right process to successfully complete the order.

View Story

Standard of Excellence: The Challenges of Hiring Good People and Methods for Success

05-17-2017

Increasingly, we hear about the challenges of finding and hiring good people in our industry. We are being hit on all sides; much of our work force is aging out while young people don’t seem to be too interested in joining the printed circuit board industry. Let’s face facts: Fewer young people are going to college to become circuit board process engineers.

View Story

Standard of Excellence: The Advantages of Flex and Rigid-Flex Circuits

05-01-2017

Since their introduction, flexible and rigid-flex circuits have been steadily moving from the fringe of electronic interconnection towards its center. Today, flex and rigid-flex circuits are found in countless products from the very simple to the highly complex. The reasons for this shift to the center are numerous; most of them are related to the advantages they offer. An examination of some of the benefits and advantages will make this clear.

View Story

Standard of Excellence: Staying Prepared with Operations

03-08-2017

Handling the operations of a PCB company these days is a challenge, to say the least. When I started in 1979, we were building single-sided, double-sided, four-layer multilayers, and the occasional six-layer if you really had your act together. We were using FR-4 materials sprinkled in with an occasional polyimide build.

View Story
Back

2016

Standard of Excellence: Selling Technology—A PCB Engineer Transitions to Sales

12-21-2016

Selling technology today takes a great deal of time, patience and most of all knowledge of the product. There was a time when a salesperson was just that, a salesperson. Now, with the onset of all the new technologies, from RF and metal backed boards to flex and rigid-flex boards, to HDI and microvia boards and heavy copper boards, a salesperson must know what he’s talking about.

View Story

Standard of Excellence: RF Microwave Technology—The Future is Now

11-29-2016

Although RF/microwave technology has been around for a considerable amount of time, many people are still not sure exactly what it is. This month, I am going to dedicate my column to explaining exactly what it is, why it is used, and in what products is it used. I’ll also discuss who needs it.

View Story

Standard of Excellence: Let’s Get Flexible

11-18-2016

Although flex and rigid-flex technology has been around for many years, it is only in recent years that it has come into its own. The reason for the increased requirements for the flex and rigid-flex technology is simple: Devices are getting smaller.

View Story

Communication Breeds Success

08-29-2016

We all need to talk to one another. You need to work closely with your customers. And we all need to work with the new generation of PCB designers and design engineers, many of whom have never set foot in a board shop. Fortunately, they make up for their lack of DFM knowledge with their hunger for information.

View Story

The Future is in Fine Lines

07-11-2016

The age of much finer lines and spaces is upon us. After years of slowly moving towards this technology our customers are now demanding that all of us provide them with fine lines and spaces.

View Story

LED and Metal-Backed Technology—Today and in the Future

05-25-2016

Probably one of the hottest, or should I say coolest, technologies today is LED. I would also venture to say it is one of the fastest growing as well...

View Story

Tips for Finding a Great PCB R&D Partner

04-06-2016

This new column, Standard of Excellence, represents a cooperative writing effort by a team of experts at American Standard Circuits. This month, we begin with CEO Anaya Vardya, who focuses on R&D. In his piece, he provides his insights on what characteristics to look for in a good R&D PCB fabrication vendor partner, and a few things that are expected of them to do for you.

View Story
Copyright © 2018 I-Connect007. All rights reserved.