Ladle on Manufacturing: Fabricating for Signal Integrity

Signal integrity! In a world which is increasingly high-speed and digital, the chemical-dependent and mainly analogue-controlled world of PCB manufacturing is not always a comfortable partner.

In theory, the electronic performance of each PCB design is protected by the tolerances and material specification stated in the design package, but the further you proceed towards the limits of technical product performance, the more difficult it is to ensure you will get a perfect result.

Start with your base material. The copper thickness may be stated as 35 microns on the delivery paperwork but what is the real thickness of the copper? A lot of companies use a simple resistance-based thickness check to make sure they are using the right thickness but that will not tell you if you are starting with 35 microns or if the actual thickness is more like 33 microns. Copper is a relatively expensive commodity, and the process for foil production can be pretty accurately controlled. This means that material suppliers may use the allowed tolerance to their advantage by keeping the foil thickness closer to the lower limit of thickness.

Now let us consider a batch of 50 production panels passing through the inner layer process. Pretty early in the process you are going to have to clean the surface of the material to ensure your dry film photoresist will stick to the surface. Cleaning may be using an abrasive brush or chemical cleaning but either way you are reducing the copper thickness further.

Production processing is not a perfect science and reprocessing of material sometimes happens. Let’s say the dry film had a wrinkle on the surface. In this case the material cannot be used unless the film is stripped and then the panel has to pass again through the surface cleaning process and be re-laminated with dry film. In the process, we lose a little bit of extra copper thickness which then means one of our production panels is a little different from the rest with regard to the remaining copper thickness.

The etching process then removes the unwanted copper leaving the desired line width on the PCB. Again—life is not perfect—there is always some variation, as fresh etch solution is usually dosed into the machine in pulses so the etch rate is not the same from one panel to the next. Our panel which already has a little less thickness than the others in the batch is a potential worst case as it started with less copper so would etch just a few percent faster than the others, meaning the final track width will also be slightly thinner than the other panels. Poor working practice may mean that an under-etched panel is re-processed through the etch, which removes the unwanted copper but also takes a little more of what should have remained on the track with it.

After stripping the dry film and inspecting the panels, they usually pass through a reducing oxide to roughen the copper surface in preparation for multilayer lamination. The oxide process takes a further skim of copper from both the height and width of the tracks.

There are some fail-safes to try to help us with the above problems. Automatic optical inspection can certainly check for over-etched panels, but in truth the capability is very limited. Nearly every machine is only able to access the width of the top surface of the track which leaves a significant open question about the shape of the sidewalls of the tracks. Undercut of the copper due to over-etching may not be apparent at inspection but it can significantly reduce the cross-sectional area of the conductor. There is also no way to be sure of the actual copper thickness remaining without a destructive microsection being taken—and there is no guarantee that every panel is the same as the next anyway.

To read the full version of this article which appeared in the October 2017 issue of The PCB Magazine, click here.



Ladle on Manufacturing: Fabricating for Signal Integrity


Signal integrity! In a world which is increasingly high-speed and digital, the chemical-dependent and mainly analogue-controlled world of PCB manufacturing is not always a comfortable partner.

View Story

Ladle on Manufacturing: Back to Basics


Many companies in the printed circuit industry are based in a single factory. When everything is going well, this can really help to get the best out of people and machinery. The main drawback is that seeing the same issues day after day, it can be easy to accept your manufacturing problems as being normal.

View Story

Ladle on Manufacturing: Why is the Developer Missing at BATM Systems’ Romania Facility?


I recently had the great pleasure to be working with BATM Systems at their new factory in Romania. The process concept is the brainchild of Steve Driver. For those who don’t know Steve, he is a gentleman of many years of experience in the UK printed circuit industry. Even after several decades of circuit production, he has an energy and enthusiasm for manufacturing which are most infectious!

View Story

Ladle on Manufacturing: Time to Show our Hand?


It can be quite tough to satisfy the product requirements of the military and aviation industries, and rightly so. There are not many other parts that we manufacture that could result in a life-threatening situation should they fail when they are in use.

View Story

Testing Times Ahead


Bare board electrical test: For the most part, it does what it says on the tin. Current CAM software and test hardware means that in theory, it is a pretty simple exercise to make sure that a printed circuit matches the intended design. But are you getting the test you think you are?

View Story

Drilling Deep


Whether you stack high or drill thick panels, the dynamics of drilling are similar. When you overlay the outer-layer artworks you may notice that the holes on the exit side of the panel or stack have a much higher level of positional variation than the entry side holes.

View Story

Material Matters


Have you considered whether or not you could improve your multilayer yields by better use of your base materials? Perhaps the following could give you a few ideas of how this could help you.

View Story


Making Suppliers Work for You


Every company has its own way of doing things. For some, the engineering team develops a detailed specification for the equipment they would like to purchase and this is put out to multiple suppliers for tender, along with full documentation for the commercial terms that will apply to the purchase. At the other end of the scale, a machine inquiry can be a simple phone call: “How much for a new machine?”

View Story
Copyright © 2018 I-Connect007. All rights reserved.