-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Advances in Medical Diagnostics Using LoC and LoPCB Technologies
March 31, 2020 | Pete Starkey and Happy Holden, I-Connect007Estimated reading time: 14 minutes
LoC Materials
Over the years, several materials have been developed for use with LoC. It started in the late 1990s with silicon, as the microelectronics industry developed various methods of micromachining silicon (MEMS) for accelerometers for airbag sensors. From silicon wafers, the materials branched out to glass and then polymers. The most recent interest has been in PCBs and the use of various paper materials.
Silicon and glass have several advantages for fabricating an LoC, while being the most expensive. Polymers and especially PCBs are a new choice because of various materials available and the integration of electronics and various printing technologies. While paper is coming into focus for research, its use is only just beginning. Table 1 lists several characteristics of each of these materials.
Table 1: Base materials for LoC formations.
1. Silicon-based
Silicon started the LoC point-of-care (PoC) diagnostic uses. Figure 6 shows one of the first on the market—the Agilent 2100 Bioanalyzer System—for DNA, RNA, serum protein, and infectious disease analysis.
Figure 6: Agilent Technology has been involved in the life sciences since 1995. Their “nanolab chips” are used to analyze DNA, RNA, SARS, and other infectious disease proteins [2].
2. Glass-based
Glass is a lower cost material if electrical components and circuitry are not required. Glass can be fabricated into microchannels and deposited with many substances such as gels and coating. The glass device seen in Figure 7 is an Agilent 3100 Bioanalyzer Automated LC/MS that comes in numerous forms to separate chemicals and biological samples into microspray streams for use with liquid chromatography/mass spectrometry (LC/MS).
3. Polymer/PCB-based
Many polymers are also optically transparent and can be integrated into systems that use optical detection techniques such as fluorescence, UV/Vis absorbance, or Raman method. Moreover, many polymers are biologically compatible, chemically inert to solvents, and electrical insulating for applications where strong electrical voltages are necessary, such as electrophoretic separation and the surface chemistry of polymers. This can also be modified for specific applications. The most common polymers used in bio-MEMS include PMMA, PDMS, OSTEmer, and SU-8.
So, what could be achieved using PCB technology? Of recent years a lab-on-printed circuit board (LoPCB) approach has been suggested. The PCB industry is mature, well-established worldwide, and has standardized fabrication processes, materials, and production equipment currently dedicated to electronics applications, but with the potential to become a natural partner for LoC development and the scope to be straightforwardly up-scaled.
Enter Dr. Despina Moschou, a researcher at the Centre for Advanced Sensor Technologies, Department of Electronic and Electrical Engineering at the University of Bath in the U.K. Dr. Moschou is a frequent speaker at printed circuit events like AltiumLive [1], EIPC Conferences, and the ICT Conferences. Fortunately, for us, she has taken the time to prepare summaries of her, and the many others in this field, work on LoC and LoPCB µTAS approaches.
Early experimentation was focused on bio-electrodes for PCBs and on the microfluidics compatible with PCB fabrication. Figure 8 shows a test vehicle. This was a two-sided FR-4 PCB with gold plated copper traces and sensor electrodes. Two different golds were tested. One was a soft gold—the Metalor R MetGold Pure ATF process, plated 2.57 µm layer of 90 HV hardness. For the hard gold, the Metalor R EnGold 2015CVR process was followed, providing 2.41 µm of gold on top of 3.41 µm of nickel with a final hardness of 140–180 HV.
To handle the delicate microfluidics, the properties of dry film photoresist (like DuPont RistonTM, or DFR) was employed. This photosensitve material, with proper curing, can be stabilized for long life, and—in some applications—can be used as a photosensitive adhesive. Too bad that the dry-film solder mask (DFSM), like DuPont VacrelTM, was no longer available. A thin FR-4 layer (200 µm) was laminated with a 50 µm DFR, that was patterned using standard PCB photolithography, developed and cured for two hours to drive off any solvents. Then, adhesive-based flexible cover coating of PMMA film was laser micromachined to provide for larger fluidic supply channels (~5 mm), and the stackup laminated to the FR-4 sensing layer.Page 3 of 5
Suggested Items
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.
Indium Corporation Expert to Present on Pb-Free Solder for Die-Attach in Discrete Power Applications
04/30/2024 | Indium CorporationIndium Corporation Product Manager – Semiconductor Dean Payne will present at the Advanced Packaging for Power Electronics conference, hosted by IMAPS, held May 8-9 in Woburn, Massachusetts, USA.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.